The word “feedback” can mean two different faults. A microphone can pick up its own sound through speakers, creating acoustic feedback. It can also pass an audible buzz, hiss or crackle that comes from the cable, connector, power path or another electrical source. Start by identifying which one you have; the fixes are different.
This guide follows the controls and checks documented by Apple for a Mac. A setting that looks correct does not prove that a cable, microphone capsule or USB port is working, so each check below states what it can and cannot rule out.
First, identify acoustic feedback or electrical noise
Acoustic feedback rises when the microphone hears sound from a speaker and that sound is sent back to the speaker. A whistle or howl that starts when monitoring is turned up, or that changes when you move the microphone, points to that loop. Mute or disconnect monitoring, move the microphone farther from the speaker, and retest before investigating the USB hardware.
Electrical noise is different. Hiss, crackle, a steady hum or a buzz may continue while the room is quiet and speakers are off. Test with headphones or another output so an amplifier or speaker is not part of the result. Do not assume a particular cable is defective until interchangeable parts have been tested.
Check the input device and input level
Open System Settings, choose Sound, then Input. Select the USB microphone rather than another input the Mac offers, such as a display or iPhone microphone. Adjust the input volume only after selecting the intended device.
If the correct microphone is absent, disconnect and reconnect it and confirm that its manufacturer supports the current macOS version. An absent device is a connection, power or compatibility issue, not evidence of a cable that happens to be “unshielded.”
Grant microphone access to the recording app
In macOS Ventura or later, open System Settings, then Privacy & Security, then Microphone. On macOS Monterey or earlier, use System Preferences, Security & Privacy, Privacy, then Microphone. Turn on access for the application you are actually using to record.
Quit and reopen that application after changing permission, because a permission that is already granted does not automatically remove an existing session problem. Apple directs people to check this access when an app cannot record from a USB microphone or audio interface.
Inspect the device in Audio MIDI Setup
Open Audio MIDI Setup, choose Window and then Show Audio Devices. Select the microphone in the sidebar and review the available input format, sample rate, bit depth, volume and clock controls. It must first appear as an available input device; the app can configure a listed device but cannot diagnose a device that never enumerates.
Available controls differ by device. Change one setting at a time and record the result rather than copying a sample rate or format from an unrelated microphone. If the interface needs manufacturer software, install the version that the manufacturer lists for the current operating system.
Collect a clean recording test
Choose a test that produces enough evidence to compare before and after. Open the recording app and select the USB microphone, disable speaker monitoring, record ten seconds of silence, then speak at a normal level for another ten seconds. Listen on headphones and look at the app’s input meter.
- Noise during silence and speech: suspect an electrical or connection path before the microphone’s acoustic environment.
- Noise only while monitoring through speakers: suspect acoustic feedback or speaker/amplifier noise first.
- No meter movement at all: check permission, selected input and the device listing before judging the audio quality.
- Clean on another port or computer: the evidence narrows the fault toward the Mac path or a cable/connector, but a single test does not prove which component failed.
Isolate the USB cable, port and adapter
Make one change at a time. Try a cable that is known to work with the microphone’s connector type, connect directly to a Mac port instead of a hub or adapter, and repeat the same silence-and-speech test. Use only a cable and power supply that meet the manufacturer’s specifications.
Longer or thinner cable runs can matter, but changing cable length is not a universal repair. If a direct, known-good connection is clean and the original path is not, that combination is stronger evidence than guessing from the appearance of a cable. Reconnect each part and check that the device still appears in Sound before opening the recording application.
Keep the test results reproducible
Note the macOS version, microphone model, application, USB path, selected input, input volume, monitoring state and result for each test. Use the same room and speaking distance when comparing recordings. This record separates a repeatable hardware symptom from a setting that changed between attempts.
If the microphone fails on several computers and with more than one suitable cable, use the manufacturer’s support path for a hardware diagnosis. Do not use an unreviewed third-party driver, a modified USB cable or a diagnostic routine from an unverified forum post to force the device to appear.
Frequently asked questions
Why does the microphone hiss when no one is speaking?
The noise is occurring during silence, which makes an acoustic loop less likely. Check the input device and permission first, then isolate the cable, port and any adapter. A setting can be correct while a connection path still introduces noise.
Why does feedback appear only when speakers are on?
That pattern points toward the microphone hearing speaker output and the signal returning to the speaker. Disable monitoring or use headphones, increase distance and lower the speaker level before treating it as a USB fault.
Does changing the sample rate fix electrical noise?
No sample rate or bit depth is a guaranteed fix for a physical or electrical problem. Review those settings because they affect device configuration, but change only settings offered by the actual device and verify the recording each time.
Where are microphone permissions on a current Mac?
In macOS Ventura or later, open System Settings, Privacy & Security, then Microphone. On macOS Monterey or earlier, the path is System Preferences, Security & Privacy, Privacy, then Microphone.
Sources
- Apple: Change the sound input settings on Mac — selecting an input device and adjusting its level.
- Apple: If you can’t record audio from an external source on Mac — microphone permissions for a USB microphone or audio interface.
- Apple: Set up audio devices in Audio MIDI Setup on Mac — the Audio Devices window and device controls.
Source review: 18 November 2026. Apple and microphone manufacturers can change these controls and requirements; verify the live instructions for your macOS version and device.
